|
|
Product Details:
Payment & Shipping Terms:
|
| SDR / Rating: | SDR 17 / Water PN10 · Gas 5 Bar | Gas Service: | Not Rated (water/HP Only) |
|---|---|---|---|
| Jointing: | Butt Fusion (DVS 2207) | Standard Radius: | 3D (custom Up To 10D) |
| Material: | Virgin PE100 Black | Manufacturing: | Mandrel Heat-Bent (no Mould) |
| Size Range: | D63 – D630mm (d110-400 Stock) | Angle: | 22° (small-angle Sweep) |
| Angles: | 60° (mid-angle Sweep) | ||
| Highlight: | 22° Ultra-Fine Angle Seamless Bend,SDR 17 Light-Wall Mandrel-Bent Sweep,PN10 Water 5 Bar Gas Seamless Bend |
||
The PE100 22° seamless bend (SDR 17) is the cost-optimised light-wall version of our ultra-fine mandrel-bent sweep. Rated to Water PN10 (1.0 MPa) and Gas 5 Bar, it is made from solid PE100 pipe heat-bent over a mandrel — continuous wall, no mould parting line, no weld seam, smooth long-radius bore.
On agricultural irrigation trunk mains, the SDR 17 wall is the sweet spot: strong enough for pump-head pressures but light and cheap enough that kilometres of buried lateral line stay economical. On sewer rising mains and outfall lines, the thin-wall bend handles routine pressurised sewage duty at a fraction of the installed cost of SDR 11. On mine site water, condensate return and low-pressure distribution, it gives the same smooth 22° micro-alignment as the SDR 11 version without over-specifying the wall.
Because SDR 17 uses less PE100 per metre, large diameters — especially d315 through d630 — become dramatically lighter to handle, less expensive to freight and faster to butt-weld on site. Where the operating pressure is PN10 or below, the SDR 17 22° bend is the rational engineering choice.
![]()
If your design pressure is PN16 water or 10 Bar gas, specify SDR 11. If the network operates at PN10 or below (irrigation, sewer rising main, mine water, low-pressure distribution, medium-pressure gas up to 5 Bar), SDR 17 gives you the same smooth 22° sweep at roughly 35–45% less weight and material cost — and large diameters become practical to handle by hand on remote sites.
The 22° SDR 17 seamless bend is available from d63mm up to d630mm. d110–400mm is standard stock at 3D centreline radius; d63–90mm and d450–630mm are produced to order. Custom angles (11°, 15°, 18°, 25°, 28° etc.) and radii (5D / 8D / 10D) are made to drawing.
| Item | Specification |
|---|---|
| Material | Virgin PE100 (Borealis / Ineos) |
| Colour | Black (with optional blue/yellow stripes for water/gas identification) |
| Standard Dimension Ratio | SDR 17 |
| Water Pressure Rating | PN10 (1.0 MPa at 20°C) |
| Gas Pressure Rating | 5 Bar |
| Bend Angle | 22° (custom angles on request) |
| Manufacturing Process | Mandrel heat-bent (no mould) |
| Standard Centreline Radius | 3D (5D / 8D / 10D on request) |
| End Type | Spigot for butt fusion |
| Size Range | d63 – d630mm |
| Standard Stock | d110 – d400mm |
| Z / L Dimensions | Per ISO 8085-3 practice — CAD / dimension table on request |
| Marking | PE100 · SDR17 · 22° · PN10/5Bar · Batch · Date |
Note: exact Z and L dimensions depend on the selected centreline radius and angle. Send your survey offset data or grade drawing for a precise dimension sheet.
All spigot fittings are manufactured from certified PE100 virgin material and tested against international piping system standards. Production is backed by ISO 9001 and ISO 29001 quality management systems.
Note: suitable for irrigation, non-potable water, sewer rising main and medium-pressure gas duty. Material certificates and test reports supplied on request.
Because SDR 17 bends use thinner wall, large diameters nest more compactly and weigh less per piece — meaning more pieces per container and lower freight cost to irrigation districts, mining sites and municipal projects.
We stand behind the quality of our spigot fittings. Our commitment doesn't end at delivery — we provide welding, angle selection and installation technical support for your irrigation, sewer, mining or low-pressure water project.
Common questions about our 22° SDR 17 light-wall seamless bend
Contact Person: Miss. Lily Wu
Tel: +86 13732670405
Fax: 86-512-57805208